CarTest - Performance Tester Взлом 1.10.2

Скриншоты

Описание

CarTest is a tool app that measures acceleration performance of cars, motorcycles.
You can easily measure times such as 0-60 mph, 0-1/4 mile by CarTest.
It is useful for not only measuring full throttle performance but also knowing the usual acceleration on public road for safe driving.
Please use it with safety first. Please comply with the law when using it on public roads.

(How to use)
1. Fix the iPhone (or iPad with GPS) with CarTest installed on the dashboard of your car so that it does not sway. If your iPhone doesn't fall while accelerating, you can just put it on the dashboard or center console. When using it on a motorcycle, install it on the handlebar or fuel tank.
2. Tap the Start button (or Start / Repeat button). If the car is stopping, “In Prep" is displayed, and if the car is moving or the device isn’t capturing GPS signal, "Waiting for Stop" is displayed. (If the device isn’t capturing GPS signal, "GPS" mark to the left of the CarTest logo shows in thin gray.)
3. When the message “Ready Go!" Is displayed, start at your own timing. You will be notified by sound at the same time as the display. When your car starts, measurement starts and "Measurement Started" is displayed. The screen becomes a green image during measurement.
4. If your car decelerate during measurement, the measurement will finish and "Finished" will be displayed.
5. If the Start / Repeat button was tapped, when the speed drops near a stop, "Waiting for Stop" is displayed to prepare for the next measurement.

(Button function)
Stop: The measurement will end immediately.
Start: Makes the measurement only once.
Start Repeat: Repeats the measurement. It is convenient for repeated measurement in urban areas where there are many signals.
share: A window opens to share the displayed result.
▲newer: After displaying the past result with ▼older button, tap this button to return to the newer results.
▼older: Displays past results from the stored history.
km/h / mph: Selects the unit of speed
↑ / ↓: Page scroll. These buttons are enable when there are other results behind while viewing history.

(Measurement range)
km/h: From 0-20 km/h to unlimited every 20 km/h. 0-400 m. 0-1 km.
mph: From 0-10 mph to unlimited every 10 mph. 0-1/4 mile. 0-1 km.

(Large speed display on the screen)
You can turn it on and off by tapping the Stop button twice in the stopping state (when neither the Start button nor the Start / Repeat button is tapped).

(Sensitivity setting of start sensing)
In the stopping state, tap buttons “Stop → ▲newer → ▼older → ▲newer → ▲newer" to open the setting window at the top of the screen. You can select 5 levels of sensitivity. Adjust if there are many false start sensing or if the response is slow. Probably no adjustment is necessary.

(Note)
1000 cases of measurement history are stored even if you quit CarTest.
When you uninstall and reinstall CarTest, the stored measurement history will be deleted.
Dark mode compatible.
No advertisement in the app.
CarTest does not work on iPads without GPS.
If the GPS signal is weak, the operation may become unstable.
The developer assumes no responsibility for any accident, violation, loss or claims by third parties which may arise from the use of this app.

CarTest - Performance Tester
Ⓒ 2020 Takao Ichimura

История обновлений

1.10.2

2022-12-07

Fixed a minor bug and improved performances.

1.10.1

2022-11-13

Fixed that sharing function by share button may not work properly on iPad.

1.10.0

2022-11-08

"copy" button has been changed to the "share" button to make it easier to share the measurement results and improve convenience.
Changed the button operation to open the setting window for sensitivity setting of start sensing to "Stop → ▲newer → ▼older → ▲newer → ▲newer”.
Other improvements.

1.9.1

2022-10-20

Fixed a minor bug and improved performances.

1.9.0

2022-10-06

Improved status messages.
Other improvements.

1.8.1

2022-07-09

Optimized the screen layout.
Other improvements.

1.8.0

2022-02-16

Adopted splash screen.
Other improvements.

1.7.0

2021-10-04

Modified the routine for “Ready”. (For motorcycles, etc. with large vibration)
Other improvements.

1.6.0

2021-09-05

Fixed a bug that speed and message were not displayed properly on some models.
The number of digits after the decimal point of the measurement time has been changed from 1 digit to 2 digits.
In Start/Repeat mode, the process to show "Waiting for Stop" in preparation for the next measurement has been changed.

1.5.1

2021-03-16

Updated for improvement

1.5.0

2021-03-08

Changed recorded time from UTC to local time.
Date and time of the measurement history display are green to make it easier to see.

1.4.0

2020-12-08

The following functions have been added.
･ Max speed in measurement is added on the screen.
･ Measured times over 0-180km/h are displayed on the screen.
･ Unlimited measurement speed.
･ While displaying the history, measured times over 0-180km/h can be checked.

1.3.5

2020-11-28

Fixed initial display in mph unit

1.3.4

2020-11-08

In order to improve convenience of checking result, in Start/Repeat mode, the speed displayed as "Waiting for a stop" in preparation for the next measurement has been reduced.

1.3.3

2020-11-03

To prevent mismeasurement, if the app enters background before a measurement starts after Stop button was tapped, the measurement is canceled.

1.3.2

2020-10-31

Even if the time by speed is not measured but the time of 0-1/4mile (or 0-400m) is measured, the measurement result is stored.

1.3.1

2020-10-26

Changed the icon

1.3.0

2020-10-25

Measured date and time are displayed along with the measurement history.
Speed display is turned off while measurement history is displayed.