Brain / iKon / Xbar / TracX Hack 3.4.103 + Redeem Codes

• Improvements, changes, and corrections to previous version 3.4.100 as per user suggestions and reports
• Added the management of new Brain2/iKon2 batch
• Revised the routine of “Tail Motor RPM2” parameter to be able to record higher speed
• Added the checkbox for VARIO telemetry also in ADVANCED
• In Spektrum Integration added the checkbox for VARIO telemetry and the loggable parameters “Rel.Altitude” & “VSpeed”
• In Graupner Integration added the checkbox for VARIO telemetry and the loggable parameters “Rel.Altitude” & “VSpeed”
• New version of “Brain2Jeti.zip” integration files (release notes inside zip file)
• New version of “Ethos_Integration.zip” files (release notes inside zip file)
• New version of “Brain2OpenTX-EdgeTX.zip” Integration for Horus transmitters (release notes inside zip file)
• Added the actual software version on the top of the firmware update window
• Changed title of the panel 3 of the Wizard from “Receiver Selection” to “Receiver Protocol Selection”
• Revised some title of Wizard to better understand which are mandatory or optional setup (for simplified and expedited setup)
• Added to the description of Basic telemetry parameters logged “RPM2” & “Ext PWM”
• Changed the description of the loggable parameter “External PWM Input” to “Ext. Std PWM Input” to make it clearer that are expected impulses with 1520uS (Std.) center pulses and not impulses with 760us center pulse
• Revised the instructions of the COUNTERS (Timers) section of the Wizard
• Revised French instructions
• New version of “README_for_ESC_datas_log_and_telemetry.pdf” document (“Tail Motor RPM2 & PWM” section)
• Improvements/optimization/compression/size reduction/speed up of the code

• Improvements, changes, and corrections to previous versions when ESC telemetry is active with F.Bus protocol
• A new LUA app for Ethos version that now works also with F.Port protocol and S.Port+S.Bus protocol, display on top bar which is the Setup (1/2/3) active whose values are shown, and added in the list of diagnostic parameters selectable in page 11 (Diagnostic) also "Rel.Altitude" and "VSpeed"
• Added decoding of a Futaba SBS-01A sensor connected to the S.Bus2 line to be able to log "Altitude" & "VSpeed" parameters in the Flight Log memory
• Added decoding of a Robbe “Vario Sensor” connected to the S.Bus2 line to be able to log "Altitude" & "VSpeed" parameters in the Flight Log memory
• Added decoding of a Graupner “GPS” sensor connected to the telemetry line on CH3 to be able to log "Altitude" & "VSpeed" parameters in the Flight Log memory
• Added decoding of a FrSky “VARIOMETER SENSOR” sensor connected to the telemetry Smart.Port on CH3 to be able to log "Altitude" & "VSpeed" parameters in the Flight Log memory
• Added the possibility of connecting a Jeti “Mvario2” sensor to SAT2 connector and decode the signal to be able to log "Altitude" & "VSpeed" parameters in the Flight Log memory also for non-telemetric receivers / protocols
• Added the possibility of connecting a Jeti “MALTI EX” sensor to SAT2 connector and decode the signal to be able to log "Altitude" & "VSpeed" parameters in the Flight Log memory also for non-telemetric receivers / protocols
• Added in the “Telemetry Input” subpanel a new “Vario” checkbox
• Now with Windows app, using the left Ctrl key of the keyboard it is possible to update the Events windows, start/stop real time logs, start/stop real time vibrations
• Added some new functions for diagnostic purpose loading an user mtr configuration file (Servo Voltage, CPU temperature, etc)
• Revised French instructions
• New “README_for_Ethos_Integration_for_BRAIN.pdf” document
• New version of “README_for_ESC_datas_log_and_telemetry.pdf” document with a new page for variometers
• Improvements/optimization/compression/size reduction/speed up of the code

• Improvements, changes, and corrections to previous version 3.4.084 when telemetry is active with F.Bus & F.Port protocol
• Added "Altitude" & "VSpeed" to the loggable parameters. The first sensor activated is the FrSky ADV VARI sensor to be connected on the F.Bus
• Updating the Events screen can now also be done using the left "Ctrl" button on the keyboard
• On page 1 of the Wizard (page that opens after each update when running the Windows app) the Internet connection status has been moved to the first position and is highlighted in red if there are problems with connection or no connection to the Internet
• In the firmware update window, added the sentence explaining that a stable Internet connection is required for the update
• Increased the number of retries during firmware updates when the Windows app connects to our update servers
• As user request, reduced the minimum values for Speed 1, 2, 3 on the Governor page from 1000rpm to 800rpm
• In ADVANCED, Common tab, Servos, the "Tail Motor Driven" selection is now only possible for tail servo 4
• Revised French instructions
• New version of “README_for_ESC_datas_log_and_telemetry.pdf” document

• Improvements, changes, and corrections to previous version 3.4.081 as per user suggestions and reports
• Revised French instructions
• New version of “README_for_ESC_datas_log_and_telemetry.pdf” document

• Added Crossfire (416.666bps) with telemetry decoding. Telemetry is transmitted to RX from CH3 connector and channels transmitted by RX are received from SAT1 connector
• Added the FrSky F.Bus icon (460.800bps) in panel 3 “Receiver Selection (Input)” of the Wizard
• Added FlySky i-Bus protocol (with telemetry) automatic recognition and decoding when the multiprotocol icon is selected
• Spektrum protocol SRXL2 can now work at higher speed (400.000bps) if all devices connected to the SRXL2 bus can rut at this speed. This permits a lower latency in the commands.
• Now regardless of whether the flight controller's governor is used or not, when the model blade length is selected in Wizard panel 10, the governor's Speed1/Speed2/Speed3 values are raised to the typical RPM values for the model size (low for large models high for small models)
• In panel n°1 “General Instructions” of the Wizard, "SAB Goblin 580 Nitro" has been added to the model selection dropdown list
• Added in panel 1 of the Wizard the item “Transmitter Mode” for a better support and statistic purpose
• In panel 5, the "Tail Gain" signal slider changes to blue color if during subsequent tail setup it was decided not to use a radio channel to control tail gain but to select the "Is set in software" checkbox. This is because in this case it will be more obvious that the tail gain slider position in panel 5 and controlled by the transmitter, cannot modify the tail gain
• Added three traffic lights in the title bar of Wizard panel 5 that indicate in real time whether the receiver and/or satellite 1 and/or satellite 2 are working or not working or whether the signal is intermittent
• Increased in panel 12 of the Wizard and in Advanced the maximum value of “Pulses for rotations” from 20 to 25 (for the new DirectDrive motor bundled in RAW 420 with 21 pairs of magnets)
• Added under “Help” menu the new files for Integration on FrSky transmitter using the new ETHOS OS (Tandem20 / 20S, Tandem18 / 18S, Horus X12S-ISRM, X10 / X10S Express)
• Released a new updated version of the Brain2OpenTX.zip file (see ReleaseNotes.txt)
• Released a new updated version of the Brain2Jeti.zip file (see ReleaseNotes.txt)
• Revised Spektrum Integration
• Revised Graupner Integration
• Added for better diagnostic purpose the following purple ESC Events:
220 "ESC: Low voltage protection" For YGE, Scorpion, Kontronik, HobbyWingV5
221 "ESC: Over current protection" For YGE, Scorpion, Kontronik, HobbyWingV5
222 "ESC: Over temperature protection" For YGE, Scorpion, Kontronik, HobbyWingV5
223 "ESC: Input throttle is not at 0% position" For HobbyWingV5
224 "ESC: Motor locked protection" For HobbyWingV5
225 "ESC: Throttle Signal loss protection" For HobbyWingV5
226 "ESC: Abnormal input voltage" For HobbyWingV5
227 "ESC: ESC lack of one phase" For HobbyWingV5
• Many additions, changes and improvements in the data saved within the configuration files, Event files and recorded Logs files, and in the management of update server data so that we can do more in-depth analysis on the files received from users and offer better support and diagnosis and remote assistance
• Revised French instructions
• Some revision of icons, connections diagram, names, titles, labels, units and instructions
• New version of “README_for_ESC_datas_log_and_telemetry.pdf” document
• Improvements/optimization/compression/size reduction/speed up of the code

• Added (only for combustion models that have a clutch: “Is Electric” not selected), the new “Failsafe Idle value” that prevents combustion engines from shutting down in the event of short radio signal interruptions (Fail Safe)
• Added decoding of the new Platinum V5 protocol of Hobbywing (used for now only on new Platinum V5 150A)
• Added for deeper diagnostic purpose purple events for the following YGE, Kontronik, Scorpion, Platinum V5 errors: “ESC: Low voltage protection”, “ESC: Over current protection”, “ESC: Over temperature protection”
• Added decoding of the new F.Bus protocol used with the new FrSky ETHOS transmitters. For now selectable only from the protocols drop-down menu in: ADVANCED => Common => Receiver
• Added a power supply voltage check that prevents the firmware update process from starting if the voltage is too low. This is because by analyzing the external event memory of the Flight Control Units that came back with the processor ROM erased and/or altered, we have seen that in these returns the events "Voltage 4,3V" are always present
• Added in the Firmware update progress windows the red phrase “Do not disconnect and do not remove power and do not close the program until the update process is finished !!!”
• Added a new message box “No Firmware selected” that appear if in the Firmware selection no firmware was selected before click on “Upload Now”
• Added the orange background that warns that the configuration of one of the Wizard panels has not been completed also in panels 9 (Tail Rotor Setup), 10 (Blades Size) and 13 (Flying Style)
• Added in the Bluetooth configuration windows the phrase “Avoid using “special” characters for NAME but use only letters and numbers.” in order to eliminate the problems encountered by some users
• Increased the minimum values for Speed 1, 2, 3 on the Governor page from 500rpm to 1000rpm following problems encountered by some users with some Speed set at 500rpm and with the model losing altitude too quickly
• If "Min V to go" has been set to a number of Lipo Cells greater than 2, but the ESC telemetry is not working due to misconfiguration or miswiring, the throttle will not lock as when there is no active ESC telemetry reading the battery voltage.
• Added in panel 14 (Final checks) an explanation of elevator swashplate movements
• Fixed the Fail Safe behavior with R3XXXXSB / R2XXXXSB receivers (FHSS) when telemetry is used using S.Bus2
• F.Port & F.Port2: eliminated occasional servo movements during Logs download
• Some revision of names, titles, labels, units, instructions & menu order (English and Italian)
• New version of “README_for_ESC_datas_log_and_telemetry.pdf” document
• Improvements/optimization/compression/size reduction/speed up of the code

• Added to the 11 Jeti telemetry transmitted values selected in the “Parameter Setup” tab of DIAGNOSTIC, also the “Log Parameter 12” value “Global Vibrations”. If an ESC is selected in “Telemetry Input” of panel 12 of the Wizard, are also transmitted “ESC Battery Voltage”, “ESC Battery Current”, “ESC Battery Used”, “ESC Battery Ripple”, “ESC Power Output”, “ESC LS RPM”, “ESC Temperature 1 (°C & °F)” values. If Hobbywing or Jive Pro or YGE are selected also “ESC Temperature 2 (°C & °F)” are transmitted. If Jive Pro or YGE are selected also “ESC BEC Current” is transmitted. A New AUTO Discover is not required, but all new parameters must be Added in “New Displayed Telemetry” if you want to see it
• Added in the File menu the “Reset Logs to default” command
• With Tandem Rotor models, by giving elevator commands the pitch increase of one rotor is greater than the pitch reduction of the other rotor to achieve a behavior of Tandem Rotors models more similar to that of single rotor models
• Rewritten, simplified and reduced size of Firmware unifying some similar routines used for S.Port+S.Bus, F.Port, F.Port2
• If FrSky Neuron ESC’s telemetry signal is connected to the S.Port bus via an “Y” cable the ESC telemetry is recognized and can be recorded in Flight Controller logs
• Added to the OpenTX the “PowerOut” pwm value (0-100%) with the sensor name “1000” (like for global vibrations, there are no predefined sensor for this kind of value in actual OpenTX versions)
• Added the Event “Voltage > 8V4” as a warning that the receiver and/or servos may be damaged at such supply voltages, and that the BEC regulator may have failed
• Added the Event “Flight Count increased” to better understand if that Event group is related to a real flight or to a bench test / ground test. Note: the “Flight Count” value in COUNTER section may not correspond to the number of Recorded Logs due to possible bench logging
• Now in all “Integrations” “Pitch Out Max:” is displayed correctly also if “Reversed Pitch” is selected
• Now using OpenTX S.Port + S.Bus protocol and connections, no more “sensor lost” message happen for VFAS sensor
• Restored the filtering of the RPM signal used by the Governor to the highest filtering values used prior to the FW versions 3.4.013 because of problems with some ESCs (Castle Creation) with high noise on RPM wires
• Starting with firmware 3.4.XXX the Spektrum Binding via Software and/or via Hardware does not work with SRXL2 receivers and the on-board bind button of the SRXL2 receivers must be used. Fixed
• Now also with the F.Port2 protocol the secondary receiver connected via “S.Bus In” to the main receiver is correctly working
• Values of Exponential’s that cause a slight change in the output values now work only for Pitch channel and not for all the other channels
• Now if the unit still has the factory firmware, the configuration software won't start if you don't update the FW to a valid version, as explained in the instructions the units must not be configured and must not fly with factory firmware
• Now the parameter selection dropdowns of the Windows configurator are opened by clicking in any area of the dropdown instead of the small button on the right as before
• In panel n°1 “General Instructions” of the Wizard, “RadioMaster" has been added to the transmitter drop-down list and "Oxy 5 Nitro" has been added to the model selection list and at the request of some users "Zigsaw AYA" has been added in the blade’s selection dropdown
• In panel n°3 “Receiver Selection” of the Wizard, in the Multiprotocol icon and lateral instructions the Spektrum SRXL2 protocol has been moved to the first position so that it can be more easily and quickly viewed by those who often select by mistake the Spektrum SRXL protocol used only by 4649T receivers
[MORE...]

• Added to the 11 Jeti telemetry transmitted values selected in the “Parameter Setup” tab of DIAGNOSTIC, also the “Log Parameter 12” value “Global Vibrations”. If an ESC is selected in “Telemetry Input” of panel 12 of the Wizard, are also transmitted “ESC Battery Voltage”, “ESC Battery Current”, “ESC Battery Used”, “ESC Battery Ripple”, “ESC Power Output”, “ESC LS RPM”, “ESC Temperature 1 (°C & °F)” values. If Hobbywing or Jive Pro or YGE are selected also “ESC Temperature 2 (°C & °F)” are transmitted. If Jive Pro or YGE are selected also “ESC BEC Current” is transmitted. A New AUTO Discover is not required, but all new parameters must be Added in “New Displayed Telemetry” if you want to see it
• Added in the File menu the “Reset Logs to default” command
• With Tandem Rotor models, by giving elevator commands the pitch increase of one rotor is greater than the pitch reduction of the other rotor to achieve a behavior of Tandem Rotors models more similar to that of single rotor models
• Rewritten, simplified and reduced size of Firmware unifying some similar routines used for S.Port+S.Bus, F.Port, F.Port2
• If FrSky Neuron ESC’s telemetry signal is connected to the S.Port bus via an “Y” cable the ESC telemetry is recognized and can be recorded in Flight Controller logs
• Added to the OpenTX the “PowerOut” pwm value (0-100%) with the sensor name “1000” (like for global vibrations, there are no predefined sensor for this kind of value in actual OpenTX versions)
• Added the Event “Voltage > 8V4” as a warning that the receiver and/or servos may be damaged at such supply voltages, and that the BEC regulator may have failed
• Added the Event “Flight Count increased” to better understand if that Event group is related to a real flight or to a bench test / ground test. Note: the “Flight Count” value in COUNTER section may not correspond to the number of Recorded Logs due to possible bench logging
• Now in all “Integrations” “Pitch Out Max:” is displayed correctly also if “Reversed Pitch” is selected
• Now using OpenTX S.Port + S.Bus protocol and connections, no more “sensor lost” message happen for VFAS sensor
• Restored the filtering of the RPM signal used by the Governor to the highest filtering values used prior to the FW versions 3.4.013 because of problems with some ESCs (Castle Creation) with high noise on RPM wires
• Starting with firmware 3.4.XXX the Spektrum Binding via Software and/or via Hardware does not work with SRXL2 receivers and the on-board bind button of the SRXL2 receivers must be used. Fixed
• Now also with the F.Port2 protocol the secondary receiver connected via “S.Bus In” to the main receiver is correctly working
• Values of Exponential’s that cause a slight change in the output values now work only for Pitch channel and not for all the other channels
• Now if the unit still has the factory firmware, the configuration software won't start if you don't update the FW to a valid version, as explained in the instructions the units must not be configured and must not fly with factory firmware
• Now the parameter selection dropdowns of the Windows configurator are opened by clicking in any area of the dropdown instead of the small button on the right as before
• In panel n°1 “General Instructions” of the Wizard, “RadioMaster" has been added to the transmitter drop-down list and "Oxy 5 Nitro" has been added to the model selection list and at the request of some users "Zigsaw AYA" has been added in the blade’s selection dropdown
• In panel n°3 “Receiver Selection” of the Wizard, in the Multiprotocol icon and lateral instructions the Spektrum SRXL2 protocol has been moved to the first position so that it can be more easily and quickly viewed by those who often select by mistake the Spektrum SRXL protocol used only by 4649T receivers
[MORE...]

• Now also the SRXL2 signal coming from the “Bind/Prog/SRXL2” port of Spektrum “base” receivers (EG: AR6610T, AR8020T) is recognized and used
• Now also the SRXL2 signal coming from the Smart Throttle output (CH1) of Spektrum “base” receivers (EG: AR6610T, AR8020T) and Spektrum “normal” receivers (EG: AR410, AR620) is recognized and used. This is the preferred way to use also “base” receivers if you want to avoid the internal RX UART for satellite connected to the receiver is disabled and used for “Bind/Prog/SRXL2” communications!!
• Improved the channel reception immunity when app’s are connected to the Flight Control Units and F.Port2 and F.Port (inverted and un-inverted) protocols are used
• Added in Spektrum Integration the new “Min V to go (cells)” parameter
• Added in Jeti Integration the new “Min V to go (cells)” parameter
• Added in FrSky Integration the new “Min V to go (cells)” parameter
• Added in Graupner Integration the new “Min V to go (cells)” parameter
• Added three new Events: n°112 = "Min V to go recognized", n°70 = "Min V to go skipped", n°115 = "Max Usable mAh reached"
• To unlock the "Min V to go" function, it now takes only two attempts to raise the throttle instead of three, and the function does not activate for values greater than two cells if an ESC telemetry is not selected or if ESC telemetry does not work (wrong setup and/or wrong connections: ESC battery voltage = 0)
• On top bar of “Receivers Channels” panels, Voltage value change to red color if below 4,7V and CPU temperature value become red when over 80°C
• Now in Demo Mode (no connected unit recognized) the window for selecting the various models of control units to emulate is immediately displayed. The initial window that indicates the absence of connected units has been removed to speed up execution times
• Added the TBS Crossfire protocol in the S.Bus protocol paragraph of the receiver panel instructions
• Renamed panel 12 of Wizard to “Throttle Out & Telemetry & Governor Setup”
• Now, when you save a flight log, the flight log number downloaded from the flight control unit is automatically proposed as file name so that it is easier to compare it with the group of Events that have the same flight number
• The format of the saved flight log files has been modified by adding the flight number in the header. When a file with this new header is reloaded, the flight number will be shown in brackets in the header of the graph also if the user has modified the file name by deleting the flight number.
• Pitch Exponential (Antigravity): Negative values caused a slight reduction in maximum pitch, now they cause instead a slight increase in maximum pitch (delta=10%)
• Tail Motor: Now also non-tail specific ESCs are triggered (EG: BLHeli with standard firmware and standard configuration)
• After this software update, with subsequent software updates both the message and update progress windows will show both the current software version number and the version number of the software you are installing
• For informational purposes only, in panel 9 "Tail Rotor Setup" the tail gain values received from the transmitter are now displayed even when the "Is set in software" checkbox is not selected (in this panel that has "Check Mode" active they have no influence)
• Added some small changes (also server-side), some new functions and some new fields in the "Support Request" to improve their management and to be able to provide more specific and faster answers
• Introduced new diagnostic functions for faster and more reliable product analysis
• New version of “README_for_ESC_datas_log_and_telemetry.pdf” document
• New version of “README_for_Spektrum_Integration.pdf” document
• New version of “README_for_Jeti_integration_for_BRAIN.pdf” document
• New version of “README_for_OpenTX_integration_for_BRAIN.pdf”
• New version of “README_for_HoTT_telemetry_and_integration_for_BRAIN.pdf”

• Introduced in the Telemetry section the new “Min V to go (cell num.)” parameter that (optionally) signals by swashplate movement of the elevator if at power on the battery pack is low (instructions in the related balloon)
• Added F.Port2 uninverted (selecting multiprotocol icon) and inverted decoding (selecting the new icon). Developed and tested with Archer R4 (FW: Archer-X_2.1.7) and with the R-XSR (FW: "RXSR_ACCESS_2.1.7") receivers. No special cable required
• Added F.Port inverted decoding (selecting the new icon). No special cable required
• Now with FrSky / OpenTX, the telemetry transmission of “Global Vibrations” value works even with Combustion models that use “Basic Telemetry” or “Also Temperature Sensor”
• Now if an Avian or Firma ESC with new 2021 firmware are used, the Brain2/iKon2 Integration is disabled to avoid conflict with ESC integration and let running at least the ESC integration that cannot disabled or firmware downgraded (for now)
• Now also some models of FlyFun ESC (Hobbywing) that sometime at “power on” enter in “PROGRAM CARD” communication mode, are now working regularly
• Modified the Twin Rotors management so that it can also work on models other than Vario models
• Improved telemetric S.Bus2 operations with Futaba T-FHSS receivers (EG: R31001SB/R008SB)
• Revised integration management on Graupner (Hott / SUMD) radio systems to improve speed
• Introduced a workaround for a problem with new firmware subsequent the version 2.1.2 released for ARCHER RS receivers when the Fail Safe is set to "No pulses"
• Improved the Bind procedure by software with SPM4650
• Raised the required value required from B-Aux1 radio channel for Auto Level / Rescue activation for user that set the range for this channel from 0% to 100% instead of -100% +100%
• Added the new panel for “Support Request” that finally send automatically to our technical support together the request also the Configuration file, the Events file and a Flight Log file. It is accessible from the Help menu or from the DIAGNOSTIC section
• After having given the command "Reset to Factory Default" from the File menu and closed the software, if you try to reopen the software without having cycled the power supply of the flight control unit as explained in the instructions, the software does not start, and a message appears indicating the user's error
• If you try to load a configuration file that is wrong or that has been saved immediately after the "Reset to Factory Default" command from the File menu, the file is not loaded, and a message appears
• If a Configuration file (MTR) is loaded in Demo Mode, panel 5 of Wizard displays the Transmitter values saved at the time the configuration file was saved
• Added in the message box that appear after a Firmware update, the phrase: ‘After updates that introduce changes to the Flight Logs, it may be necessary to reinitialize the Flight Log memory by re-formatting it with the "Erase Logs memory" command.’
• To select the flight control unit kind you want use in Demo Mode now just double click on it (no more select it, then move to “OK” button and push)
• Wizard panel 2 enhanced final paragraph for internal combustion engines
• When Spektrum SRXL2 or SRXL rx is selected, in the message box that appear when “Spektrum bind” checkbox is selected added the phrase: “Re-power the unit not from USB but from the servo connectors to power also the receiver connected to the CH3 connector”
• Wizard panel 3 “Receiver Selection”, when old Brain or Micro Brain are connected (or emulated in Demo mode), in the multiprotocol icon, the SRXL2 and F.Port protocol not working with these units are forbidden for more clarity
• Added instructions for B-Aux3 in panel 5 of Wizard
• Added in “Servo chart Cyclic” old Futaba S3050 servo
• Now in the panel 8 of the Wizard the eventual writing "Swashplate not selected" is all in capital and in red color
[MORE...]

• Introduced the possibility to control Tandem Rotors models such as the Vario Chinook
• Added the possibility to log RPM also from a second electric motor (EG: model with tail motor or model with two motors like Velos)
• Added the possibility to read and record in the Flight Logs the value of a PWM signal output from an external device
• Added the possibility to control through an additional radio channel assigned to the new B-Aux3 function, a PWM signal output on the CH4 connector to control an additional function in addition to the B-Aux2 one already present on the CH2 connector. To disable PWM Output set B-Aux3 to “No Channel”
• Now even with standard receivers with separate channels wires, the QOS values of the received signal are calculated and therefore also with these receivers the parameters "RxFrameRate mS", RxFades n°", Frame Losses n°", Holds n°" can be recorded in the flight logs memory
• Added to the loggable parameters “Global Vibrations” value
• Added to telemetric parameters manageable via Jeti telemetry “Global Vibrations”
• Added to telemetric parameters manageable via Spektrum telemetry “Global Vibrations” under the emulated sensor “Fuel Status”. “Fuel Consumed” is the instantaneous value of “Global Vibrations” for which the alarm can be set, “Flow Rate” is the maximum value of “Global Values” reached during flight
• Added to telemetric parameters manageable via S.Port (OpenTX) telemetry “Global Vibrations” under the emulated sensor “Fuel”
• Added to telemetric parameters manageable via F.Port (OpenTX) telemetry “Global Vibrations” under the emulated sensor “Fuel”
• Added for diagnostic purpose to the loggable parameters “CPU Temperature C°”. This value is also now visible on the top bar of channels panels at the right of “(servo voltage = x,x V)”
• Added the two new events “Check Mode Activated” & “Check Mode Disactivated”. This let know to some user why during setup Throttle do not work and why green led go to off
• Added the new event “Loaded a Configuration File”
• Now telemetry values are read also from old Platinum V3 ESC’s. Only RPM & Power Output (PWM). If ESC governor is used, Power Output can be very useful to verify that the used gear ratio is correct
• Added the new loggable parameter "ExtRxVoltage" which is the voltage read by the auxiliary connector ("extra voltage") available on some Futaba receivers (already telemetrically transmitted on the RX slot 0)
• Now with SPM4649T receivers the voltage seen on “Telemetry” page of TX for “Volts” sensor is that read from the “V Batt” connector of the 4649T RX (in the “Flight Log” page the voltage reported for “Receiver” continue to be the Servo Voltage of Brain2 as before)
• Now Fades calculations work with SRXL2 protocol also with DX6 or DX7 Gen2 EU version transmitters working only at 22ms (it is required a new 4651T firmware that responds as required by the protocol, to the bind status interrogation)
• Revised the range of Fine tuning by dials / potentiometers / Trim increasing PID range for tail, aileron and elevator with some update of the min and max values
• For those who, after setup, use pitch curves with reduced negative values (reproductions, some beginners, etc.), the storage of dials values are now also performed with collective pitch values between -100% and zero
• Eliminated repetitions of EVENTS when the motor fast start of Autorotation Bailout is running
• Revised for F.Port the “Frame Rate” calculation due to the different frame rate in ACCST mode (9ms) and in the new ACCESS mode (7ms)
• Eliminated the annoying false alarms generated with SRXL2 receivers if during setup with a USB powered control unit the power is removed and restored to the receiver and servos
• When in demo mode, if a configuration file is loaded, the type of control unit from which the file has been saved is recognized and the correct scheme for that type of unit is displayed
[MORE]

• Added the ability to log FrSky RSSI reading from S.Bus channel n°16 (RSSI is always measured from channel 16, the receiver, if it is a model able to send RSSI, must be set to send RSSI value pushing bind button for 5 seconds. With this mode channel 16 cannot be used as a normal channel)
• Increased the MAX value of “Rx Frame Rate uS” to 1000 also if it is not graphically visible to be able to intercept the cause of a Throttle Fail Safe
• Solved Fades calculation problem with SRXLv2 RX when one or two DSMX sat are added (this problem did not affect the reception of radio channels or telemetry but only the calculation of the receiver's Fades)
• In Advanced, if Fast Tail Servo are selected for Swashplate servo 0,1,2,3 now correct values for maximum Throw are activated (for Tail Servo 4, as before, half maximum throw are selected to avoid binding)
• Added in “Servo Chart Tail” Align DS825M servo
• In the graphs of the DIAGNOSTIC section, make small corrections of the vertical scales of the input and output signals of Elevator and Ailerons
• New version of README_for_ESC_datas_log_and_telemetry.pdf document
• Revised French instructions
• Revised some names, titles, labels, units, instructions (English and Italian)
• Improvements/optimization/compression/size reduction/speed up of the code

• Added the management for logging in real time or into Flight logs also the Spektrum AVIAN / FIRMA ESC telemetry data
• Added in the Spektrum Integration (only) the telemetry selection also for Spektrum AVIAN / FIRMA ESC
• Added a message if “Also Spektrum AVIAN / FIRMA ESC telemetry” is selected when SRXL2 is not selected
• For the old Brain/iKon control units (1) the automatic reporting of obsolete firmware to be updated has been restored following numerous reports of problems due only to the incredibly old firmware used
• For F.Port protocol used with ACCESS transmission (7mS frame rate) improved the flow of telemetry data’s
• Events: further increased the delta value that trigger and un-trigger the event “Throttle output limit reached”
• During firmware update if an error occurs, now software does not close itself, but an error message with explanations is generated
• Wizard panel 3 “Receiver Selection (Input)”: added info’s related to the telemetry with S.Bus or S.Bus2
• Wizard panel 3 “Receiver Selection (Input)”: added info’s about satellite’s type when Spektrum SRXL2 or SRXL is selected
• Wizard panel 3: after "PPM/SUMO", "Spektrum DSM2" & "Spektrum DSMX” instructions, added some info’s related to ESC/Thermal telemetry
• Modified under the top “?” menu, the label “About” in to “Release Notes”
• On the start of Release Notes completed and cleared which are the SW and FW actual versions
• Revised the random number generator in Demo Mode for Servo Voltage to do not exceed 8,4V
• Added in the Motor Type list of page 1 of the Wizard “Egodrift” brand
• Download Flight Logs window: now it is possible to directly download a Flight Log with a double click on it
• Under DIAGNOSTIC => Vibration tab the value for the new Global Vibrations” parameter become red if greater than 200
• New version of README_for_ESC_datas_log_and_telemetry.pdf document
• New version of README_for_Analogic_integration_by_TX_dials.pdf document
• New version of README_for_Spektrum_Integration.pdf document
• New version of README_for_Jeti_integration_for_BRAIN.pdf document
• New version of README_for_OpenTX_Integration.pdf document
• New version of README_for_HOTT_telemetry_and_integration_for_BRAIN.pdf document
• New version of README_for_MSH51610_Dongle_Bluetooth_Brain.pdf document
• Revised Russian instructions
• Revised French instructions
• Revised labels, instructions and balloons (English and Italian) also some labels / names on integrations
• Improvements/optimization/compression/size reduction/speed up of the code

• All FrSky sensors emulated to transmit ESC values have had their Application ID changed. This allows to connect other sensors of the same type (but with different Data IDs) to the Smart.Bus. E.g. other thermal sensors, other voltage sensors, etc. This require a new sensor discover
• Added a fix for the OpenTX Integration of Servo Frame rates
• For Nitro users, now like for Futaba temperature sensor, also for FrSky temperature sensor (named RPM sensor by FrSky) connected to the FrSky Smart.Port bus (by an “Y” connection) Temperature1 and Temperature2 values can be recorded in the Flight Logs memory of the units
• Added a message when for Telemetry Input the “Futaba Temperature Sensor” is selected and SBUS protocol RX is selected in the Receiver Selection
• In “Receiver Selection (Input)” panel of the Wizard, changed the icon for multi-protocol (SRXL2, SRXL, UDI, F.Port, X-bus-b, SUMD)
• In “Receiver Selection (Input)” panel of the Wizard, changed the icon for “Spektrum SRXL” protocol, adding the name of the only receiver able to use this protocol (SPM4649T)
• Added a different message when Spektrum bind checkbox is selected when SRXL2 Spektrum or SRXL Spektrum receiver connected to CH3 port are selected
• In “Connections” panel of the Wizard, updated all the schematics with the H-4X swashplate and with the optional (dotted) governor connections and the optional (dotted) telemetric connections and the optional (dotted) Spektrum satellites
• Revised the firmware update process. Initial cancellation now does not start if bidirectional communication is not full working
• Added a reference to the new “Release Notes” in to the “Firmware update done” message
• Now immediately after loading a configuration file, a confirmation message appears
• Added a warning message if in the “Bluetooth Configuration” window “Write” key is pressed in Demo Mode
• Added in “Servo Charts Cyclic” the Futaba BLS156HV and SAVOX SB-2283MG servos
• In the "Blades Size Selection" panel of the Wizard, the internal text of the 3 blades icon has been changed from "3 BLADES" to ">2 BLADES" so that those who do not read the instructions will be clearer that the selection is for 3, 4, 5, 6, 7, ... blades.
• Instructions of Wizard panel 12 ”Governor”: modified recommended values of throttle for speed1 from 40% to 45% and for speed2 from 60% to 65%
• ADVANCED, Common, Receiver, Receiver Type: aligned the order of the selection curtain for protocols with the same order of the instructions and icons in the "Receiver Selection" panel of the Wizard
• Launching the Brain2 software from the command prompt using “ -demomode” parameter, the scanning of virtual com’s is skipped
• Advanced, Common, Receiver, modified in the “Receiver Type” curtain, the label "NEW HoTT-Sumd / UDI / Xbus-B / Mpx-SRXL" in to "NEW HoTT-Sumd / UDI / Xbus-B / Mpx-SRXL / SRXL2 / FPort"
• Events: increased the delta value that trigger and un-trigger the event “Throttle output limit reached”
• Events: modified "Acceleration >= 16g" to "Deceleration >=16g"
• Events: modified "Resetted to Factory defaults" to "Reset to Factory defaults"
• DIAGNOSTIC: in the Vibrations tab added the new value “Global Vibrations” that correspond to the vibrations area / surface and must be lower than 200
• DIAGNOSTIC: in the Vibrations tab changed the grey area to evidence the vibrations at low frequency
• DIAGNOSTIC: added the description of the unit of measurement used in the vertical vibration scale
• DIAGNOSTIC: In the “Recorded Logs” tab, changed the cursor from a vertical line to a cross to be able to intercept the lateral scale values
• DIAGNOTIC: renamed “RxAux1 %” to “RxB-Aux1 %”, “RxAux2 %” to « RxB-Aux2 %”, “RxAux3 %” to “RxB-Aux3 %”
• When Configuration file is saved (“MTR” files), all the actually transmitted value from TX are saved at the end of the file for DIAGNOSTIC / SUPPORT purpose

• Corrected in OpenTX Integrations “Servo0 angle” displayed value
• Corrected in OpenTX Integrations “Blade Number” & “Blade Length” functions when “Flybarred” is selected
• Added a workaround fix for the OpenTX Bug that when Fail Safe is set to “No Output”, instead of sending no signal, send -115% signals to all channels and then set fail safe flag. From now on, out of range values so high are discarded
• Improved timing for H130R & H140R swashplates movements to eliminate some little interactions
• Introduced a workaround for users with Spektrum DXe or DXi transmitters that works only with DSMX 22ms protocol to connect to two DSMX satellites binded by our flight controller at 11mS
• Added under Help menu the Help Online submenu (FAQ, How To, Forum, Blog)
• Added to names of Wizard panels 2 and 3 “(Input)”. Added to names of Wizard panels 6 and 7 “(Output)”
• Updated version of Brain.bin file for Jeti Integration
• Revised French instructions
• Revised labels, instructions and balloons (also some labels / names on integrations)
• Improvements/optimization/compression/size reduction/speed up of the code

• With Spektrum telemetry, on the transmitter “Telemetry” page of Voltage/RPM/Temperature the Temperature value displayed is the higher between Temp1 and Temp2
• With NEW SRXLv2 protocol, the automatic assignment of channel is executed also after a Bind process
• After an automatic assignment of channels, the Channel Assignments page in Advanced -> Common -> Receiver, is updated
• When in panel “Receiver Selection” of the Wizard an already selected icon is selected/clicked again no change of the channel assignment is done to the default values (default values are loaded only during the change of the selected icon)
• With F.Port receiver, improved Integration transmissions for Servos parameters
• Now at factory reset all servo output are disactivated
• New Wizard panels layout to prevent radio channel signals from being wrongly reversed to correct servo directions
• Added in the Brain2FrSky.zip some transmitters configuration examples (OTG files)
• Revised labels, instructions and balloons (also labels on integrations)
• Improvements/optimization/compression/size reduction/speed up of the code

• From now the Aux channel is separated in to two different channels, one (B-Aux1) dedicated to the Auto Leve / Rescue function and the other (B-Aux2) dedicated to the CH2 output. During the first update the new B-Aux2 channel is set equal to the actual B-Aux1 channel so for users there is any change from the actual configuration.
• Now to the CH2 output can be assigned a different radio channel from that used for the Auto Level / Rescue activation and used independently for the control of Buzzers, Turn On GlowPlug, Position Lights, Retractable Landing gear, Smoke Generators, Servo to adjust the carburation, etc. etc.
• Added H-4X swashplate icon in the “Swashplate Type Selection” page of the wizard and in the selection curtain of “Swashplate Type” in the Advanced => Common => CCPM. Selecting this Swashplate kind, the CH2 output is assigned and controlled by the CCPM Mixer and the B-Aux2 parameter shown in the "Transmitter Setup (Input)" panels is removed. This function don’t work with standard receivers and PPM/SUMO Receivers.
• Revised in Advanced => Common the panel "CCPM" to show the new parameter "Servo 0 Angle (yellow):" that it is activated and graphically displayed only when the swashplate H-4X is selected
• Added in Advanced => Common => Servos the panel for the regulation of “Servo 0/Aux2/CH2” parameters
• Added in Spektrum and Graupner Integrations the selection for Swashplate CCPM H-4X and in Diagnostic the selection for the loggable B-Aux2 channel
• Added in Spektrum and Graupner Integrations in the Servo section all the regulations of the CH2 output (Servo0)
• Added in Jeti telemetry the possibility to select the RxAux2 value
• Now when in the “Swashplate Type Selection” panel, H-1 swashplate is selected (EG: Raptor), in the successive panel “Swashplate Setup (Output)” it is possible to regulate the excursion of “Pitch” and “Cyclic” servos precedent assigned only to CCPM Mixers without the need to go in Advanced (removed instructions of this). When H-1 swashplate is selected value for Pitch and Cyclic start both at 50%
• Now the minimum value for Ramp Up can be reduced to 2 (from 3 before) for scale models.
• Wizard “Tail Setup”: now user can see values changes and it is no more “blind” when “+” and/or “-“ buttons are pressed. Introduced limits to maximum and minimum values so that Tail Servo can no longer go out of sync and stop working
• Little reduction of the default values for maximum tail rotations when a “Flying Style” is selected in the Wizard. This to reduce the complaint from user for “Rudder output limit reached” Events
• Now, when a new Firmware update is available, in the window asking whether to update (Ok) or postpone the update (Cancel), no buttons are preselected anymore. The user must choose and decide what to do to move forward.
• Fixed a problem with binding via software of SPM4649T introduced with 3.2.060 which forced bind using bind plug
• Added in “Servo Charts” MKS Servo-tech HV93 and Lynx DS 895-HV Spektrum SPMSH3050 and SPMSH3060 servos
• Added Instructions for B-Aux2 in panel 6 and for CCPM H-4X swashplate in panel 7
• New version of README_for_ESC_datas_log_and_telemetry.pdf document
• New version of README_for_OpenTX_Integration.pdf document
• New version of “README_for_Spektrum_Integration.pdf” document
• Revised French instructions
• Some other grammatical corrections in the instructions and Label / Parameters Names
• Minor graphic changes
• Improvements/optimization/compression/reduction/speed up of the code

• Added the decoding of the new F.Port protocol used by FrSky selecting the “SUMD/UDI/Xbus-B/SRXLv2/Mpx-SRXL 12 & 16ch / unidirectional Spektrum SRXL” icon / protocol
• Improved the new Spektrum SRXL v2 protocol for future receivers: Better measure of Fades and other than RSSI dBm now is managed also RSSI %
• Now S.Bus protocol is also able to decode S.Bus signal coming from RadioLink receivers
• Doubled the frame rate speed with Futaba S-FHSS receivers
• Now each time the “SUMD / UDI / Xbus-B /SRXLv2 / SRXL Spektrum (unidirectional old receivers) / Mpx-SRXL 12 & 16Ch / F.Port” icon / protocol is selected for the first time, other than automatically recognizing of the right protocol also the channel assignment is automatically changed and adapted to the specific protocol
• Now with FrSky during the use of the integration there should be no "Sensor Lost" signals at all
• FrSky Integration it is now twice as fast as before (finally “acceptable”) is now more "consistent" and is no more slowed down if no sensor or 20 sensors are active and onnected to the Smart.Port bus.
• Now FrSky Integration officially work also on Taranis Q X7 ACCST
• The recognition and setup of the new "Tail Motor Driven" has also been added in all the Integrations (Spektrum, Jeti, Graupner, FrSky)
• For the setup of Motor Tail driven, the tail sensor inversion reading has been implemented to give feedback to users (now when you use Tail Motor and click on the Tail Reverse icon in the Tail panel of the wizard, the “virtual” servo changes appearance)
• “Tail Motor" has also been added in the list of parameters assignable to the timers
• Tail motor can now be used also with Mini Brain2 units other than Micro Brain2 units
• With Tail Motor, improved the automatic Pyro Compensation
• When a factory reset is done, the new default value for “Pulses for rotation” is now 3
• In Wizard panel 12 & in Advanced -> Common -> “Thrott&Gov if checkbox "Motor is electric" is deselected & “Pulses for rotation” is greater than 3, “Pulses for rotation” value is changed to 1. If “Motor is electric” is selected and “Pulses of rotation” value is less than 3 “Pulses of rotation is changed to 3.
• Added in “Servo Charts” Align DS450, Align DS455, BK7003HV e BK7007HV servos
• Renamed the Brain AUX channel to B-AUX1 to avoid possible confusion to users with AUX1 (Pitch) of Spektrum transmitters (S-AUX1)
• Increased the delay of the telemetric transmission from 4 to 5 seconds to let BEC Voltage stabilize more
• The maximum value of the "ESC Current" parameter graphs (instantaneous current) has been increased from 200A to 220A.
• Added the new loggable parameter “SRXL receiver %" (used by new SRXL2 receivers) in all the app
• DIAGNOSTIC: Added unit of measure symbols to all the parameters descriptions used in Flight logs
• If the unit is in Boot Loader an ad hoc message is presented and the firmware update cannot be canceled.
• Timers: put confirmation message before timer reset
• Timers: if a configuration file (MTR) is loaded, the four resettable timers are not overwritten
• In panel 4 “Receiver Selection” of the wizard revised in the instructions the order of receivers following the order of the icons (from left to right and from top to bottom)
• If for any reason the telemetric signal of the esc does not reach the control unit on the transmitters for the value "Throttle" is shown "0" and no more 50%
• New version of README_for_ESC_datas_log_and_telemetry.pdf document
• New version of README_for_OpenTX_Integration.pdf document
• Revised French instructions
• With Spanish language when you select “Load config. from File …” the configuration files on PC are now visible
• Some grammatical corrections in the instructions and Label / Parameters Names
• Minor graphic changes
• Improvements/optimization/compression/reduction/speed up of the code

IMPORTANT NOTE: Immediately after the update, go to panel 7 of the Wizard and check that your swashplate is selected (or if in panel 8 of the wizard appear the message “SWASHPLATE NOT SELECTED”). IF ANY SWASHPLATE IS SELECTED: Select the correct kind of swashplate used on your model (a unit power cycle can be required), then check that swashplate movements are correct. If swashplate movement are not correct go into the panel 8 and:

Check that SRV-1 of the top left displayed swashplate is connected to SRV1 input of the unit, SRV-2 in to the SRV2 input and SRV-3 in to the SRV3 input.
If required, correct swashplate movements with “Servo Reverse” button.

• Wizard: moved panel 9 “Unit Orientation” to panel 2, all other panels are scaled by one position
• Added further controls for the swashplate displayed as selected in panel 7 of the Wizard
• Added message “SWASHPLATE NOT SELECTED” in panel 8 of the Wizard if swashplate was not correctly done
• Now it is possible to log also values of Z-Acceleration, X-Acceleration and Y-Acceleration (in G units)
• Added in parameters that can be managed with Jeti telemetry Z-Acceleration, X-Acceleration and Y-Acceleration
• From this version it is officially added the decoding of new Spektrum SRXLv2 protocol used by Spektrum for their new receivers (for now only SPM4650) selecting the “HoTT/SUMD/UDI/Xbus-B/SRXLv2/Mpx-SRXL(oldest Spektrum rx)” icon / protocol with possible physical redundancy using 1/2 DSMX satellites
• Checkbox “Spektrum Bind” to put by software RX/SAT in to bind mode, now work also when Spektrum SRXv2 protocol is selected
• Wizard panel 9 & ADVANCED, Tab Common, Receiver: now when the Tail Gain checkbox "Is set in Software" was selected (or unselected), the radio channels for “Tail Gain” and "Setup Selection" are automatically exchanged between them
• Introduced a further improvement in current measurement with Hobbywing ESC’s
• Updated version of JETI integration file brain.bin inside the downloadable “Brain2Jeti.zip” file with all the recent firmware and software changes
• Renamed the JETI integration file under “Help” menu and on the server from “Brain.zip” to “Brain2Jeti.zip”
• New version of FRSKY script file for integration Brain2.luac inside the downloadable Brain2FrSky.zip file
• Simplified, optimized and speeded the code and greatly reduced the total size of the precompiled FrSky LUAC script to leave the RAM space for other little LUA script running in background.
• Now external sensors connected on the FrSky Smart.Port bus no more freeze the FrSky Integration
• Now FrSky Integration during the use, no longer generates the tedious messages of "Telemetry lost"
• Now the FrSky Integration doesn’t hang when particular values are read or written
• Revised some FrSky Integration menu
• Improved the “Tail Motor driven” routines for Micro Brain2 now selectable also via Integrations
• Added a control of maximum number of characters inserted in the NAME and PIN fields of “Configure Bluetooth” window
• Revised length of fields of NAME and PIN in the “Configure Bluetooth” window
• Added Spanish instructions selectable under Language menu
• Revised French instructions
• New version of README_for_ESC_datas_log_and_telemetry.pdf document
• New version of README_for_OpenTX_Integration.pdf document
• New version of README_for_Jeti_integration_for_BRAIN.pdf document
• In Panel 8 of the Wizard increased the maximum values imputable in CYCLIC and PITCH fields for particular Heli Models with particular swashplate geometry where the servo harms cannot increase (EG: Gaui X3)
• Revised the Framerate calculation for FrSky S.Bus (1 not 2) that has a framerate different (9ms) from the official Futaba S.Bus framerates standard (7ms or 14ms)
• DIAGNOSTIC section, “Real Time” tab: moved buttons over values
• DIAGNOSTIC section, “Recorded Logs” tab: moved buttons over values
[More]

• Added in firmware routines for FrSky Integration management
• Added a new power graphic engine for Logs/Vibrations/Events (license payment)
• Added the new menu “Real time Logs”
• Added the new menu “Recorded Logs”
• Added the new menu “Vibrations” (Real time and recorded)
• Added the new menu “Events”
• In the MANUALS section added the icon for the opening of FrSky manual
• Added the new function to change the PIN and NAME of Bluetooth dongle also for devices that do not have the USB "on board" (such as Micro and Mini Brain2) executable either via Remote USB or directly via Bluetooth connection (also with iOS APPs connected via Bluetooth.
• Implemented all the required functions for “download data from unit”, “Save graphics data to file”, “Clear screen”, “Selection of visible data”, etc.
• Landscape versions implemented for all menu and pages with automatic orientation active
• When app is closed or suspended, the Bluetooth state return to the state before the app is launched
• In Demo Mode Bluetooth is turned off if it was off when app is open/launched
• Dedicated text explaining how to program the Bluetooth module PIN and NAME when a Micro or Mini is connected via Bluetooth or Remote USB
• Activated the new “Tail Motor Driven” routines (for Micro Heli only, so, for Micro Brain2 only)
• Wizard page 2: added the new "Tail Motor Driven" icon selectable only with Micro Brain2 unit
• Added the new “Proportional Tail Gain by TX” subpanel in Advanced, Setup, Tail
• In Advanced, Setup, Tail changed the label from "Proportional Gain by SW" to "Proportional Tail Gain by SW"
• Advanced -> Setup -> Tail: Moved "Proportional Tail Gain (SW and TX)" groups to the beginning before “Integral” & “Derivate” gains (PID sequence)
• Instructions of Wizard panel 5 modified to “Tail Gain: Set the gyro gain so that it shows an initial starting value of 45% on the panel.”
• Now with a “Reset to factory default”, "Tail Pitch Precompensation" and "Tail Cyclic Precompensation" values are also set to work on models with clockwise rotors (99% of models) instead of being set to zero. This should simplify the tail setup
• Now with a “Reset to factory default”, Tail Gain “I” value is changed from 25% to 30%
• Advanced -> Setup -> Tail: In the tooltip of "Integral Gain" changed from 25 to 30 the factory default value
• Wizard panel 6: the light on of CW e CCW icons takes into account also the "Tail Asymmetry" value
• Advanced -> Setup -> Tail: exchanged "Tail Asymmetry” & "Tail speed" so, now all parameters related to main rotor direction (Pitch Pre-compensation, Cyclic Pre-compensation, Asymmetry) are contiguous
• Added in “Tail Servo Chart” the KST DS565X tail servo
[More...]

• Only on iX12 Spektrum transmitter with actual iX12 firmware, during the changes of values with Integration some random symbols are displayed on screen (EG: “???”): Patched
• When Jeti protocol is used, some fake “Elevator sensor out of range” appear in the events. Fake events eliminated
• Only using Futaba S.Bus2 protocol, only using Castle Creation ESC and only when Live Link is active in the ESC, some tail kicks happen, solved
• The MIN, MAX, AVG values of parameter 10 of the logs when zoomed don’t correspond to the displayed zoomed graphics but to the values of the full graphics. Fixed
• The vertical scale of ThrottleOut is now the same of RxThrottle
• When “Kontronik Jive, Power Jive, Heli Jive telemetry” is selected, the “mAh Correction Factor” is active
- When software is launched in demo mode, for each parameters the factory default values are loaded, so new users can have a better and more complete experience
- Totally revised the connection to the Windows application via Bluetooth and removed all the possible cause of delay during the initial connection (little time reduction)
- New French resources
- Improvements/optimization/compression/reduction/speed up of the code

Release notes:
- 3.2.010 (firmware 3.2.010) 9 May 2018
• Now "Aileron output limit reached", "Elevator output limit reached" and "Tail output limit reached" events are recorded only when throttle is above 20% (below Nitro’s Hold value)
• Added an automatic correction factor for instantaneous and consumed current with HobbyWing ESC when flying with small size models or at low RPM with small and medium size models
• Removed “Trial version” from diagnostic graph (this may require uninstalling and reinstalling the software)
- Fixed either tail kick and throttle cut that happen in some configurations to some users after 3.2.000 update
- Added a warning message if user try to activate “Auto Level” / “Rescue, in all three setups at the same time!
- Added some MKS servos for Cyclic and Tail in Servo Lists (at page 1 and page 2 of the Wizard)
- Added in page 1 of the Wizard, under “Model” selection T-Rex 550E PRO DFC Electric
- Updated version of "README_for_ESC_datas_log_and_telemetry.pdf" in the MANUALS page and Windows menu
- New German resources
- New French resources

- 3.2.000 (firmware 3.2.000)
• Added management of the telemetry of new YGE *VT ESC's
• Implemented the changed (from Kontronik before the imminent release) Kontronik ESC protocol
• Added for Nitro/Gasser, the management of telemetry log and transmission of a digital temperature sensor (Jeti: MT300EX, Futaba: SBS-01T) with sensor signal connected on CH5 and powered from an "Y". Work for ALL protocol selected (with Futaba S.Bus2 receivers the Futaba temperature sensor can be directly connected on the S.Bus2)
• Added Multiplex MSP telemetry. Now on Multiplex transmitters can be displayed: “Main Battery Voltage”, “Main battery instantaneous current”, “Main Rotor RPM”, “ESC Temperature”, “Temperature 2”, “Main Battery used mAh” (Protocol selection icon and connection schematics updated)
• Added with Dial regulation, the possibility to change the value of "mAh Max Discharge" (that cause a reduction of 20% of RPM) parameter by a transmitter channel (can be used a three positions switch for three different variations), other than with "Integrations"
• Now it is possible to operate the Units on Flybarred models with a simple click (anyway useful for: Tail Gyro, Governor, Auto Level, Rescue, Timers, Logs of internal data's, Vibrations, Events, Esc Logs, Telemetry, Transmitters Integrations, Dials for fine setup, all kind of receivers decoding, CCPM mixer, Smartphone setup, etc.)
• Added the new loggable values "Bailout Timer" and Temperature1 F° and Temperature2 F° (Fahrenheit) to the already present Temperature1 C° and Temperature2 C° (Celsius), in Windows, Android, iOS apps and in Spektrum, Graupner and Jeti integrations. Now the loggable parameters are 39
• Added 9 new Events: "Logs Recording Started", "Voltage <= 4V3", "Bailout Timer ended", "Watchdog Reset", "Resetted to Factory defaults", "Throttle gone in Fail Safe", "Aileron output limit reached", "Elevator output limit reached", "Logs memory was erased". Now the Events kinds are 38
• Changed "Wrong accels values" Event description to "Unit not level at startup. Check unit orientation" and other little revision of Event names
• Changed name of SRXL Fades to Rx Fades, and now Rx Fades, Frame Losses and Holds are elaborated and can be logged for all the serial selected protocols (but not for "Standard PWM Receiver")
• Changed all "Autorotation Timer...." occurrences to "Bailout Timer..." in Events, Logs, Menu, of windows, Android, iOS, and Spektrum, Graupner, Jeti integrations
• Changed loggable parameters names from "SwashAileron" to "AileronOut" and SwashElevator" to "ElevatorOut"
• Now on all telemetry (Spektrum, Futaba, Jeti, Graupner, Multiplex, *FrSky*) for RPM if any RPM sensor is connected to the GOV connector, the RPM read from ESC is sent (if a telemetric ESC is connected, otherwise zero is displayed)
• Now the receiver Fail Safe channels signal is recognized and logged also for FrSky and SUMD receivers other than for Futaba and SRXL receivers
• Revised page 3 instructions "Receiver Selection" explaining that also Graupner "SUMO" can be received, also Spektrum "PPM" can be received (EG: AR7700), also Spektrum "REMOTE RX" can be received (EG: AR7700) and that with "oldest Spektrum receivers" (EG: AR9020, AR7700) the unidirectional SRXL can be used, and that with older Spektrum receivers the bind must be manually done with a bind plug on the receiver as usual
• In wizard page3 instructions, under "Hott/SUMD/UDI/Xbus-B/Mpx-SRXL, instead of (no Spektrum) corrected to (oldest Spektrum RX)
• Added in the panel 3 instructions "Receiver Selection" the "FrSky" paragraph
• New FrSky schematics where is clearer that the MSH51645 accessory is not an option but a requirement
• In wizard page 6 revised the position of swashplates icons

[MORE]

- 3.1.027 (firmware 3.1.027)
• Added telemetry for Kosmik, Jive Pro, Kolibri, Kontrol-X ESC's. Is needed a new firmware release for the ESC not yet released from Kontronik, and a cable with the 5 pole kontronik connector
• Added for OpenTX Transmitters and FrSky receivers with Smart Port the Brain2 telemetry transmission of ESC data's (is needed a special cable adapter)
• Added in Governor pages (Wizard & Advanced) the “mAh Max Usable”. If ESC telemetry and governor are either active and the "Battery Used mAh" value raise this new tunable value (mAh Max Usable), the pilot is advised by a RPM reduction of ~20%. Factory Default value: 7000mAh
- Improved the governor function for combustion models (Nitro/Gasser) that use a servo for control the motor output power
• Added in DIAGNOSTIC the possibility to also display the RPMs normally recorded together vibrations as a new eleventh parameter (ONLY FOR NEW LOGS AND VIBRATIONS RECORDED WITH THIS NEW FIRMWARE OR SUCCESSIVE)
• The RPM displayed as eleventh parameter is the filtered RPM used by Governor and can be compared to the unfiltered RPM signal coming from sensor
• Added the new loggable parameter for SPM4649T "SRXL receiver dBm" (is needed at least the new firmware 1.1.9 for SPM4649T released from Spektrum)
• Added the new loggable parameter "Rx/SwTailGain"
• Added the new loggable parameter "TailOut"
• Renamed the loggable variable “DSMX SAT's Lost Frames” to "DSMX SAT's Frame Losses” as called by Spektrum
• Now for fastest operation when re-enter into the Spektrum Integration, the position (menu row, sub menu row, displayed value) is the same left at the Integration exit
• On Spektrum Integration, Governor menu, moved the "Throttle Out MAX" after the "Throttle Out MIN" as is the normal order
• Added in Spektrum Integration, under Diagnostic the possibility to select as loggable the five RX parameters (DSMX SAT1 fades, DSMX SAT2 Fades, DSMX SRXL Fades, Frame Losses, Holds) and the two new parameters "Rx/SwTailGain" and "TailOut"
• Added in Graupner Integration under Diagnostic the possibility to select as loggable the two new parameters "Rx/SwTailGain" and "TailOut"
- Updated all schematics of wizard page 4 related to "Spektrum SRXL" protocol, with added SAT's as optional, for schematics of Brain, microBrain, microBrain2, miniBrain2, Brain2, Brain2+BT, Brain2-HD, Brain2-HD+BT (Brain and iKon)
- Increased the Minimum Value for "Rescue Pitch Max" from 50% to 60% because at 50% to some user with very low RPM the model doesn't raise but loses quota
- Improved electric noisy field immunity of Spektrum SAT's connector (EG: if a sat cable is connected to SAT1 or SAT2 port but without any sat connected on the other side the antenna done by cable don't read wrong data's)
• In the Log reversed the polarity of the "Rx Aileron" & "AileronRotationRate °/Sec" signals so, now correspond to the polarity of the "Transmitter setup" panel
- Now when a hardware error is recognized during startup sequence, Throttle Out is blocked to MIN for security reason, (it is not even possible to program esc's with the stick)
• Added for Futaba telemetry a control of the MAX Current read from Futaba/Robbe CURR-F1678 sensor to 163.8A to avoid possible overflow
• In Spektrum and Graupner Integrations reduced the minimum value of overall Cyclic gains from 10 to 7 (for micro tri blades heli) like in Windows software
• Now the new download protocol used for Events, download all the 200 last events and not only the last 175 for all kind of "2" units
• Activated the new download protocol that no more work at a fixed low speed but work proportionally to the PC speed also for "Recorded Logs Download" from unit
• Activated the new download protocol that no more work at a fixed low speed but work proportionally to the PC speed also for "Recorded Vibration Download" from unit
[More]

• Added management of the new "HoTT + telemetry" protocol and the relative connection schemas
• Added Graupner "Telemetry"
• Added Graupner "Integration"
• Ex Bus telemetry: further revised many parameters names that now are more obvious on TX (to update names, is needed a new "SENSORS AUTO DISCOVER")
• Ex Bus telemetry: It is not possible reduce the servos frequency below 92Hz: Fixed
• Ex Bus integration: released new version of "brain.bin" file and PDF readme instructions (downloadable from MSHELI website)
- New faster autorotation bailout ramp from the governor engage (50%) point to the target RPM (pay attention if you have high "Bailout Ramp" value!)
- Governor: improved the overspeed control with nitro's
- New Boot Loader 1.7 Now is possible put the unit in Boot Loader mode shorting the TX & RX of SYS also with longer cables and also shorting CH4 & CH5 at power up (mainly for Brain2 units with Bluetooth and without the SYS connector)
- Saved in the Brain memory some new model information's (Model type, Main Blades type, Tail Blades types, Cyclic Servos type, Tail Servo type, Motor type, ESC type, Battery type, etc.) to simplify/automate/speed up the setup of the unit
- Choosing from the first page of Wizard, one of the listed Tail Servos and/or one of the listed Cyclic Servos, if the unit is in factory reset, the values in the Wizard panel 2 "Servo Setup" are set to the specified values
- Choosing from the first page of Wizard, one of the listed Models, if the unit is in factory reset, the values of the Wizard "Swashplate Type selection" and "Blades Size Selection" are set to the specified values for that model.
- Separated Servos chart for cyclic and for tail in the panel 2 "Servo Setup" of the wizard
- Now doing a double click on the row of the servo in the Servos chart, the servo chart displayed values are automatically set in to the Brain
- Added in the Servos Charts Align DS530 & DS535 standard version and "M" version and MKS DS1220, DS1230, DS1240
• Now Factory Defaulted unit record/log by default ten flight parameters at the maximum sampling rate
• In the Log reversed the polarity of the "Swash Aileron" signal so, now correspond to the polarity of the "Transmitter setup" panel
• Added a check to avoid using the same radio channel for different Calibration Channels (Dials)
• Revised variables names: RxRoll->RxAileron & SwashRoll->SwashAileron
- If radio channel assigned to "Tail gain", is disactivated with the checkbox "Is set in software", the same channel also if it is present but "greyed out" can be used for other functions
- In Advanced->Setup the active Setup is now highlighted
- Added the new "README_for_HOTT_telemetry_and_integration_for_BRAIN.pdf" in the MANUALS page
- Updated version of "README_for_ESC_datas_log_and_telemetry.pdf" (ESC telemetry work also with Futaba T-FHSS used by T10J & T6K-V2)
- Updated version of "README_for_Jeti_integration_for_BRAIN.pdf" (use of menu key for incremental value, added graphic page for vibrations)
- Also Tail servos signal is now turned off before a firmware update to avoid displacement at the start of the firmware update that sometime happen (for update from this firmware on)
- Improved/increased/completed the Blades Size range displayed inside the icons of panel 10 "Blade Size Selection" of the wizard
- In Basic->Servo Setup: added the new kind of dotted border around the icons if the relative default values are changed from the user
- In Basic->Blades Size Selection: added the new kind of dotted border around the icons if the relative default values are changed from the user
- In Basic->Flight Style Setup: added the new kind of dotted border around the icons if the relative default values are changed from the user
- Advanced->Common->Governor, added calculators for main gear and for tail gear calculation (as in Wizard)
[More]