eMaxMobileApp Hack 1.63 + Redeem Codes

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.63 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.

All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)

new in version 1.62 (21.03.23):
- minor optimizations and bug fixes

new in version 1.61 (02.03.23):
- minor optimizations and bug fixes

new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added

new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)

new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)

new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added

new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types

new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units

new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)

new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units

new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
- new battery type BT-E8016 added

ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.62 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.

All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

new in version 1.62 (21.03.23):
- minor optimizations and bug fixes

new in version 1.61 (02.03.23):
- minor optimizations and bug fixes

new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added

new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)

new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)

new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added

new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types

new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units

new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)

new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units

new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
- new battery type BT-E8016 added

ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.61 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.

All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

new in version 1.61 (02.03.23):
- minor optimizations and bug fixes

new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added

new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)

new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)

new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added

new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types

new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units

new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)

new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units

new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
- new battery type BT-E8016 added

ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.59 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.

All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added

new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)

new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)

new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added

new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types

new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units

new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)

new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units

new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
- new battery type BT-E8016 added

ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.58 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 and EW-EN100 display types.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.

All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)

new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)

new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added

new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types

new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units

new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)

new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units

new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
- new battery type BT-E8016 added

ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.066

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.57 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 and EW-EN100 display types.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.

All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)

new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added

new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types

new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units

new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)

new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units

new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
- new battery type BT-E8016 added

ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.066

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.56 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 and EW-EN100 display types.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.

All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added

new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types

new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units

new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)

new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units

new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
- new battery type BT-E8016 added

ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.066

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.55 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 and EW-EN100 display types.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.

All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types

new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units

new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)

new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units

new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
- new battery type BT-E8016 added

ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.066

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.54 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUE80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units

new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)

new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units

new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
- new battery type BT-E8016 added

ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.53 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUE80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.53 (08.07.22):
-minor fixes (darkmode & typo)

new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units

new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
- new battery type BT-E8016 added

ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.51 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUE80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units

new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
- new battery type BT-E8016 added

ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.51 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.

new in version 1.51 (29.03.22):
-update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
-update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
-update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
-32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
-update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
-update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
-optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
-new battery type BT-E8016 added

ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.50 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.

new in version 1.50 (15.03.22):
-update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
-update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
-32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
-update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
-update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
-optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
-new battery type BT-E8016 added

ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.49 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.

new in version 1.49 (22.02.22):
-32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
-update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
-update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
-optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
-new battery type BT-E8016 added

ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.48 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.

new in version 1.48 (24.12.21):
-update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
-update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
-optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
-new battery type BT-E8016 added

ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.47 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.

new in version 1.47 (25.11.21):
-update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
-optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
-new battery type BT-E8016 added

ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.46 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.

new in version 1.46 (18.11.21):
-optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
-new battery type BT-E8016 added

ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.45 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.

new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
-new battery type BT-E8016 added

ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved

ver. 1.39 (31.01.21):
-integration of new motor firmware version 4.1.2 for EP8
-extended light indication for EP8 (off/manual/on & max. power)
-chainring - size and sprocket size with all possible correct values now for EP8
-correction of indication of motor firmware version
-correction of minor text errors

ver. 1.38 (26.11.20):
-new battery type BT-E8036 added
-special settings (derailleur type, etc.) added for DUEP800

ver. 1.36 (08.11.20):
-partial compatibility with new firmware versions added (with warning) DUE50X0 [4.4.2], DUE61X0 [4.6.0], DUE7000 [4.6.0], DUE80X0 [4.9.0], DUEP800 [4.1.1]
-licence placeholdertext in darkmode improved (grey)
-new battery types added
-correction of AS - settings
-optimized "dark mode" handling for licence key entry boxes
-light activating functionality added
-motor mounting angle added
-optimized country specific decimal characters for total distance (odd)

ver. 1.35 (31.08.20):
-integration of DUEP800: compatibility with motor firmware 4.0.0 - 4.0.2 (USA - modification and wheel circumference modification)
-minor bug fixing and optimizations

ver. 1.34 (13.07.20):
-DUE80X0: compatibility with newest motor firmware 4.8.0

ver. 1.33 (18.05.20):
-6100, 6110, 6180 and 7000 series drive units with motor firmware 4.4.0 - 4.5.0 accepted
-6001, 6010, 6050 series drive units with current motor firmware 3.4.7 accepted
-6002, 6012 series drive units with current motor firmware 3.4.0 accepted
-5000, 5080 series drive units with current motor firmware 4.2.0 - 4.3.0 accepted

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. Motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.44 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.

- new in version 1.44 (03.06.21):
-- update to newest firmware version 4.1.5 for DUEP800

- ver. 1.43 (05.05.21):
-- chainring & rear sprocket size for DUE5xxx and DUE6xxx added

- ver. 1.42 (17.04.21):
-- new battery type BT-E8016 added

- ver. 1.41 (11.04.21):
-- new battery types added
-- bugfix (profile 2 EP8-RS default translation error)

- ver. 1.40 (06.04.21):
-- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-- update to fw. 4.7.2 for DUE7000
-- update to fw. 4.1.4 for DUEP800
-- profiles added for EP8/EP8-RS
-- reduced max. speed for EP8 added
-- smallest sprocket for EP8 set to 10 (instead of 11)
-- dark mode issue on light settings solved

- ver. 1.39 (31.01.21):
-- integration of new motor firmware version 4.1.2 for DUEP800
-- extended light indication for DUEP800 (off/manual/on & max. power)
-- chainring - size and sprocket size with all possible correct values now for DUEP800
-- correction of indication of motor firmware version
-- correction of minor text errors

- ver. 1.38 (26.11.20):
-- new battery type BT-E8036 added
-- special settings (derailleur type, etc.) added for DUEP800

- ver. 1.36 (08.11.20):
-- partial compatibility with new firmware versions added (with warning) DUE50X0 [4.4.2], DUE61X0 [4.6.0], DUE7000 [4.6.0], DUE80X0 [4.9.0], DUEP800 [4.1.1]
-- licence placeholdertext in darkmode improved (grey)
-- new battery types added
-- correction of AS - settings
-- optimized "dark mode" handling for licence key entry boxes
-- light activating functionality added
-- motor mounting angle added
-- optimized country specific decimal characters for total distance (odd)

- ver. 1.35 (31.08.20):
-- integration of DUEP800: compatibility with motor firmware 4.0.0 - 4.0.2 (USA - modification and wheel circumference modification)
-- minor bug fixing and optimizations

- ver. 1.34 (13.07.20):
-- DUE80X0: compatibility with newest motor firmware 4.8.0

- ver. 1.33 (18.05.20):
-- 6100, 6110, 6180 and 7000 series drive units with motor firmware 4.4.0 - 4.5.0 accepted
-- 6001, 6010, 6050 series drive units with current motor firmware 3.4.7 accepted
-- 6002, 6012 series drive units with current motor firmware 3.4.0 accepted
-- 5000, 5080 series drive units with current motor firmware 4.2.0 - 4.3.0 accepted

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. Motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.43 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.

- new in version 1.43 (05.05.21):
-- chainring & rear sprocket size for DUE5xxx and DUE6xxx added

- ver. 1.42 (17.04.21):
-- new battery type BT-E8016 added

- ver. 1.41 (11.04.21):
-- new battery types added
-- bugfix (profile 2 EP8-RS default translation error)

- ver. 1.40 (06.04.21):
-- update to newest firmware version 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-- update to newest firmware version 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-- update to newest firmware version 4.7.2 for DUE7000
-- update to newest firmware version 4.1.4 for DUEP800
-- profiles added for EP8/EP8-RS
-- reduced max. speed for EP8 added
-- smallest sprocket for EP8 set to 10 (instead of 11)
-- dark mode issue on light settings solved

- ver. 1.39 (31.01.21):
-- integration of new motor firmware version 4.1.2 for DUEP800
-- extended light indication for DUEP800 (off/manual/on & max. power)
-- chainring - size and sprocket size with all possible correct values now for DUEP800
-- correction of indication of motor firmware version
-- correction of minor text errors

- ver. 1.38 (26.11.20):
-- new battery type BT-E8036 added
-- special settings (derailleur type, etc.) added for DUEP800

- ver. 1.36 (08.11.20):
-- partial compatibility with new firmware versions added (with warning) DUE50X0 [4.4.2], DUE61X0 [4.6.0], DUE7000 [4.6.0], DUE80X0 [4.9.0], DUEP800 [4.1.1]
-- licence placeholdertext in darkmode improved (grey)
-- new battery types added
-- correction of AS - settings
-- optimized "dark mode" handling for licence key entry boxes
-- light activating functionality added
-- motor mounting angle added
-- optimized country specific decimal characters for total distance (odd)

- ver. 1.35 (31.08.20):
-- integration of DUEP800: compatibility with motor firmware 4.0.0 - 4.0.2 (USA - modification and wheel circumference modification)
-- minor bug fixing and optimizations

- ver. 1.34 (13.07.20):
-- DUE80X0: compatibility with newest motor firmware 4.8.0

- ver. 1.33 (18.05.20):
-- 6100, 6110, 6180 and 7000 series drive units with motor firmware 4.4.0 - 4.5.0 accepted
-- 6001, 6010, 6050 series drive units with current motor firmware 3.4.7 accepted
-- 6002, 6012 series drive units with current motor firmware 3.4.0 accepted
-- 5000, 5080 series drive units with current motor firmware 4.2.0 - 4.3.0 accepted

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. Motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.42 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.

- new in version 1.42 (2021_04_17):
-- new battery type BT-E8016 added

- new in version 1.41 (2021_04_11):
-- new battery types added
-- bugfix (profile 2 EP8-RS default translation error)

- new in version 1.40 (2021_04_06):
-- update to newest firmware version 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-- update to newest firmware version 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-- update to newest firmware version 4.7.2 for DUE7000
-- update to newest firmware version 4.1.4 for DUEP800
-- profiles added for EP8/EP8-RS
-- reduced max. speed for EP8 added
-- smallest sprocket for EP8 set to 10 (instead of 11)
-- dark mode issue on light settings solved

- new in version 1.39 (31.01.2021):
-- integration of new motor firmware version 4.1.2 for DUEP800
-- extended light indication for DUEP800 (off/manual/on & max. power)
-- chainring - size and sprocket size with all possible correct values now for DUEP800
-- correction of indication of motor firmware version
-- correction of minor text errors

- new in version 1.38 (26.11.2020):
-- new battery type BT-E8036 added
-- special settings (derailleur type, etc.) added for DUEP800

- new in version 1.36 (08.11.2020):
-- partial compatibility with new firmware versions added (with warning) DUE50X0 [4.4.2], DUE61X0 [4.6.0], DUE7000 [4.6.0], DUE80X0 [4.9.0], DUEP800 [4.1.1]
-- licence placeholdertext in darkmode improved (grey)
-- new battery types added
-- correction of AS - settings
-- optimized "dark mode" handling for licence key entry boxes
-- light activating functionality added
-- motor mounting angle added
-- optimized country specific decimal characters for total distance (odd)

- new in version 1.35 (31.08.2020):
-- integration of DUEP800: compatibility with motor firmware 4.0.0 - 4.0.2 (USA - modification and wheel circumference modification)
-- minor bug fixing and optimizations

- new in version 1.34 (13.07.2020):
-- DUE80X0: compatibility with newest motor firmware 4.8.0

- new in version 1.33 (18.05.2020):
-- 6100, 6110, 6180 and 7000 series drive units with motor firmware 4.4.0 - 4.5.0 accepted
-- 6001, 6010, 6050 series drive units with current motor firmware 3.4.7 accepted
-- 6002, 6012 series drive units with current motor firmware 3.4.0 accepted
-- 5000, 5080 series drive units with current motor firmware 4.2.0 - 4.3.0 accepted

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. Motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.41 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

- new in version 1.41 (2021_04_11):
-- new battery types added
-- bugfix (profile 2 EP8-RS default button translation error)


- new in version 1.40 (2021_04_06):
-- update to newest firmware version 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-- update to newest firmware version 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-- update to newest firmware version 4.7.2 for DUE7000
-- update to newest firmware version 4.1.4 for DUEP800
-- profiles added for EP8/EP8-RS
-- reduced max. speed for EP8 added
-- smallest sprocket for EP8 set to 10 (instead of 11)
-- dark mode issue on light settings solved

- new in version 1.39 (31.01.2021):
-- integration of new motor firmware version 4.1.2 for DUEP800
-- extended light indication for DUEP800 (off/manual/on & max. power)
-- chainring - size and sprocket size with all possible correct values now for DUEP800
-- correction of indication of motor firmware version
-- correction of minor text errors

- new in version 1.38 (26.11.2020):
-- new battery type BT-E8036 added
-- special settings (derailleur type, etc.) added for DUEP800

- new in version 1.36 (08.11.2020):
-- partial compatibility with new firmware versions added (with warning) DUE50X0 [4.4.2], DUE61X0 [4.6.0], DUE7000 [4.6.0], DUE80X0 [4.9.0], DUEP800 [4.1.1]
-- licence placeholdertext in darkmode improved (grey)
-- new battery types added
-- correction of AS - settings
-- optimized "dark mode" handling for licence key entry boxes
-- light activating functionality added
-- motor mounting angle added
-- optimized country specific decimal characters for total distance (odd)

- new in version 1.35 (31.08.2020):
-- integration of DUEP800: compatibility with motor firmware 4.0.0 - 4.0.2 (USA - modification and wheel circumference modification)
-- minor bug fixing and optimizations

- new in version 1.34 (13.07.2020):
-- DUE80X0: compatibility with newest motor firmware 4.8.0

- new in version 1.33 (18.05.2020):
-- 6100, 6110, 6180 and 7000 series drive units with motor firmware 4.4.0 - 4.5.0 accepted
-- 6001, 6010, 6050 series drive units with current motor firmware 3.4.7 accepted
-- 6002, 6012 series drive units with current motor firmware 3.4.0 accepted
-- 5000, 5080 series drive units with current motor firmware 4.2.0 - 4.3.0 accepted

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. Motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.40 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

- new in version 1.40 (2021_04_06):
-- update to newest firmware version 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-- update to newest firmware version 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-- update to newest firmware version 4.7.2 for DUE7000
-- update to newest firmware version 4.1.4 for DUEP800
-- profiles added for EP8/EP8-RS
-- reduced max. speed for EP8 added
-- smallest sprocket for EP8 set to 10 (instead of 11)
-- dark mode issue on light settings solved

- new in version 1.39 (31.01.2021):
-- integration of new motor firmware version 4.1.2 for DUEP800
-- extended light indication for DUEP800 (off/manual/on & max. power)
-- chainring - size and sprocket size with all possible correct values now for DUEP800
-- correction of indication of motor firmware version
-- correction of minor text errors

- new in version 1.38 (26.11.2020):
-- new battery type BT-E8036 added
-- special settings (derailleur type, etc.) added for DUEP800

- new in version 1.36 (08.11.2020):
-- partial compatibility with new firmware versions added (with warning) DUE50X0 [4.4.2], DUE61X0 [4.6.0], DUE7000 [4.6.0], DUE80X0 [4.9.0], DUEP800 [4.1.1]
-- licence placeholdertext in darkmode improved (grey)
-- new battery types added
-- correction of AS - settings
-- optimized "dark mode" handling for licence key entry boxes
-- light activating functionality added
-- motor mounting angle added
-- optimized country specific decimal characters for total distance (odd)

- new in version 1.35 (31.08.2020):
-- integration of DUEP800: compatibility with motor firmware 4.0.0 - 4.0.2 (USA - modification and wheel circumference modification)
-- minor bug fixing and optimizations

- new in version 1.34 (13.07.2020):
-- DUE80X0: compatibility with newest motor firmware 4.8.0

- new in version 1.33 (18.05.2020):
-- 6100, 6110, 6180 and 7000 series drive units with motor firmware 4.4.0 - 4.5.0 accepted
-- 6001, 6010, 6050 series drive units with current motor firmware 3.4.7 accepted
-- 6002, 6012 series drive units with current motor firmware 3.4.0 accepted
-- 5000, 5080 series drive units with current motor firmware 4.2.0 - 4.3.0 accepted

- new in version 1.32 (26.04.2020):
-- "motor performance settings" and "special settings" added to DUE7000 drive unit
-- optimization and correction for DUE50X0

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to process a speed tuning with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.39 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE800X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

- new in version 1.39 (31.01.2021):
-- integration of new motor firmware version 4.1.2 for DUEP800
-- extended light indication for DUEP800 (off/manual/on & max. power)
-- chainring - size and sprocket size with all possible correct values now for DUEP800
-- correction of indication of motor firmware version
-- correction of minor text errors

- new in version 1.38 (26.11.2020):
-- new battery type BT-E8036 added
-- special settings (derailleur type, etc.) added for DUEP800

- new in version 1.36 (08.11.2020):
-- partial compatibility with new firmware versions added (with warning) DUE50X0 [4.4.2], DUE61X0 [4.6.0], DUE7000 [4.6.0], DUE80X0 [4.9.0], DUEP800 [4.1.1]
-- licence placeholdertext in darkmode improved (grey)
-- new battery types added
-- correction of AS - settings
-- optimized "dark mode" handling for licence key entry boxes
-- light activating functionality added
-- motor mounting angle added
-- optimized country specific decimal characters for total distance (odd)

- new in version 1.35 (31.08.2020):
-- integration of DUEP800: compatibility with motor firmware 4.0.0 - 4.0.2 (USA - modification and wheel circumference modification)
-- minor bug fixing and optimizations

- new in version 1.34 (13.07.2020):
-- DUE80X0: compatibility with newest motor firmware 4.8.0

- new in version 1.33 (18.05.2020):
-- 6100, 6110, 6180 and 7000 series drive units with motor firmware 4.4.0 - 4.5.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6001, 6010, 6050 series drive units with current motor firmware 3.4.7 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6002, 6012 series drive units with current motor firmware 3.4.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 5000, 5080 series drive units with current motor firmware 4.2.0 - 4.3.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- adjustment of max. assist ratio value for DUE to 250%


- new in version 1.32 (26.04.2020):
-- "motor performance settings" and "special settings" added to DUE7000 drive unit
-- optimization and correction for DUE50X0

- new in version 1.31 (31.03.2020):
-- optimization and correction for DUE50X0
-- minor fixes and improvements

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to process a speed tuning with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via [email protected].

This version 1.38 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE800X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

- new in version 1.38 (26.11.2020):
-- new battery type BT-E8036 added
-- special settings (derailleur type, etc.) added for DUEP800

- new in version 1.36 (08.11.2020):
-- partial compatibility with new firmware versions added (with warning) DUE50X0 [4.4.2], DUE61X0 [4.6.0], DUE7000 [4.6.0], DUE80X0 [4.9.0], DUEP800 [4.1.1]
-- licence placeholdertext in darkmode improved (grey)
-- new battery types added
-- correction of AS - settings
-- optimized "dark mode" handling for licence key entry boxes
-- light activating functionality added
-- motor mounting angle added
-- optimized country specific decimal characters for total distance (odd)

- new in version 1.35 (31.08.2020):
-- integration of DUEP800: compatibility with motor firmware 4.0.0 - 4.0.2 (USA - modification and wheel circumference modification)
-- minor bug fixing and optimizations

- new in version 1.34 (13.07.2020):
-- DUE80X0: compatibility with newest motor firmware 4.8.0

- new in version 1.33 (18.05.2020):
-- 6100, 6110, 6180 and 7000 series drive units with motor firmware 4.4.0 - 4.5.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6001, 6010, 6050 series drive units with current motor firmware 3.4.7 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6002, 6012 series drive units with current motor firmware 3.4.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 5000, 5080 series drive units with current motor firmware 4.2.0 - 4.3.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- adjustment of max. assist ratio value for DUE to 250%


- new in version 1.32 (26.04.2020):
-- "motor performance settings" and "special settings" added to DUE7000 drive unit
-- optimization and correction for DUE50X0

- new in version 1.31 (31.03.2020):
-- optimization and correction for DUE50X0
-- minor fixes and improvements